Influencia da termociclagem, escovação mecanica e desinfecção quimica na dureza Knoop e rugosidade de superficie de resinas acrilicas com diferentes ciclos de polimerização
Andrea Fabiana de Lira
TESE
Português
T/UNICAMP L67i
[Influence of thermocycling, mechanical brushing and chemical disinfection on the Knoop hardness and surface roughness of acrylic resins with different cycles of polymerization]
Piracicaba, SP : [s.n.], 2010.
90 p. : il.
Orientador: Rafael Leonardo Xediek Consani
Tese (doutorado) - Universidade Estadual de Campinas. Faculdade de Odontologia de Piracicaba
Resumo: Este trabalho avaliou o efeito da termociclagem, escovação mecânica e desinfecção química na dureza e rugosidade de resinas com diferentes ciclos de polimerização. Foram confeccionadas 480 amostras (25 mm x 14 mm x 3 mm) e distribuídas aleatoriamente em 3 grupos de acordo com as resinas:...
Ver mais
Resumo: Este trabalho avaliou o efeito da termociclagem, escovação mecânica e desinfecção química na dureza e rugosidade de resinas com diferentes ciclos de polimerização. Foram confeccionadas 480 amostras (25 mm x 14 mm x 3 mm) e distribuídas aleatoriamente em 3 grupos de acordo com as resinas: Onda Cryl (G1), QC-20 (G2) e Clássico (G3). Metade das amostras foi submetida a ensaio de rugosidade e a outra metade a ensaio de dureza, antes e após os tratamentos: controle, escovação mecânica ou desinfecção química (hipoclorito e Efferdent) com e sem termociclagem. Amostras G1 foram confeccionadas, polimerizadas em micro-ondas com potência de 900 W; G2 foram polimerizadas a 100°C por 20 minutos e G3 foram polimerizadas a 74°C por 9h. As amostras foram desincluídas e acabadas em politriz com refrigeração à água, em ordem decrescente de granulação. A desinfecção química foi realizada com: 1) Hipoclorito de sódio a 0,5% a 37 ± 1ºC, durante 20 minutos; 2) Peróxido de Hidrogênio, a 37 ± 1ºC, durante 15 minutos. Após as desinfecções, as amostras foram lavadas e imersas em água destilada a 37 ± 1ºC, pelo período restante das 24 h. O processo foi repetido 8 vezes por dia, durante 90 dias (720 ciclos). A escovação mecânica foi conduzida em máquina MSEt à taxa de 5 movimentos por segundo (20.000 ciclos) e as amostras foram avaliadas sem e com envelhecimento térmico com imersões de 60 segundos a 5 ± 1ºC e 55 ± 1ºC, simulando 2 anos. Rugosidade média de superfície foi verificada pela leituras realizadas transversalmente à direção de movimentos lineares de escovação. A dureza Knoop foi verificada, sob carga de 25g/Força de penetração por 5 segundos, em cinco mensurações, antes e após a aplicação dos tratamentos. Foi realizado teste de Kruskal-Wallis e Dunn, Mann-Whitney e Wilcoxon, com 5% de significância. Resultados: Onda-Cryl apresentou dureza (KHN) antes e após os métodos, sem termociclagem, diferença estatisticamente significante (p = 0,013), enquanto entre as resinas com termociclagem, Onda-Cryl (p = 0,001) e QC 20 (p = 0,002) apresentaram diferenças estatisticamente significantes. QC 20 apresentou rugosidade média antes e após os métodos, sem termociclagem, diferença estatisticamente significante (p = 0,003), enquanto entre as resinas com termociclagem, Onda-Cryl (p = 0,046) e QC 20 (p = 0,010) apresentaram diferenças estatisticamente significantes. Entre os métodos sem termociclagem: O peróxido revelou diferença estatisticamente significante na dureza, apenas para Onda-Cryl e na rugosidade, apenas para QC 20 em relação aos métodos peróxido e o hipoclorito. Entre os métodos com termociclagem: Os grupos controle, escovação e peróxido revelaram diferença estatisticamente significante na dureza para Onda-Cryl; o método controle para resina QC 20 e os métodos peróxido e Hipoclorito para Clássico, enquanto a rugosidade revelou diferenças estatisticamente significantes para Onda Cryl em relação ao método peróxido e QC 20 para os métodos peróxido e hipoclorito. Conclusão: houve diferença estatisticamente significante relativa à Dureza apenas para o método controle nas resinas Onda-Cryl e QC 20 independentemente da termociclagem. Não houve diferença estatisticamente significante relativa à rugosidade independentemente da associação entre termociclagem, resinas e métodos
Ver menos
Abstract: This study evaluated the effect of thermocycling, mechanical brushing and chemical disinfection on the hardness and roughness of resins with different polymerization cycles. 480 samples were prepared (25 mm x 14 mm x 3 mm) and distributed randomly into three groups according to the resins:...
Ver mais
Abstract: This study evaluated the effect of thermocycling, mechanical brushing and chemical disinfection on the hardness and roughness of resins with different polymerization cycles. 480 samples were prepared (25 mm x 14 mm x 3 mm) and distributed randomly into three groups according to the resins: Onda-Cryl (G1), QC-20 (G2) and Classic (G3). Half of the samples were tested as roughness and the other half for testing the hardness, before and after treatments: control, mechanical brushing or chemical disinfection (hypochlorite and Peroxide) with and without thermocycling. G1 samples were fabricated, cured in the microwave with power of 900 W, G2 were polymerized at 100° C for 20 minutes and G3 were polymerized at 74° C for 9h. The samples were deflasked polishing and finished in water-cooled, in decreasing order of grain. The chemical disinfection was carried out with: 1) Sodium hypochlorite 0.5% at 37 ± 1º C for 20 minutes, 2) Hydrogen Peroxide at 37 ± 1º C for 15 minutes. After disinfection, the samples were washed and immersed in distilled water at 37 ± 1º C, for the remainder of 24 h. The process was repeated eight times daily for 90 days (720 cycles). The mechanical brushing was conducted in machine MSET at 5 moves per second (20,000 cycles) and the samples were evaluated with and without thermal aging with dips of 60 seconds to 5 ± 1º C and 55 ± 1º C simulating 2 years. Average surface roughness was determined by readings taken transversely to the direction of linear motion of brushing. Knoop hardness was observed under load 25g/Power penetration for 5 seconds, five measurements before and after treatments. Was performed using the Kruskal-Wallis and Dunn, Mann-Whitney and Wilcoxon, with 5% significance level. Results: Onda-Cryl presented hardness (KHN) before and after methods, without thermocycling, a statistically significant difference (p = 0.013), while among the resins with thermocycling, Onda-Cryl (p = 0.001) and QC 20 (p = 0.002) showed statistically significant differences. QC 20 had average roughness before and after methods, without thermocycling, a statistically significant difference (p = 0.003), while among the resins with thermocycling, Onda-Cryl (p = 0.046) and QC 20 (p = 0.010) were statistically different. Among the methods without thermocycling: The peroxide showed a statistically significant difference in hardness only to Onda-Cryl and roughness, only QC 20 in relation to methods peroxide and hypochlorite. Among the methods thermocycling: Control groups, mechanical brushing and peroxide showed statistically significant difference in hardness for Onda-Cryl; the control method for QC 20 resin and methods for peroxide and hypochlorite Classic, while the roughness, showed statistically significant differences for Onda-Cryl in relation to the peroxide method and 20 for QC methods peroxide and hypochlorite. Conclusion: statistically significant difference on hardness only to the control method in the resins Onda-Cryl and QC 20 regardless of thermocycling. There was no statistically significant difference on the association between roughness regardless of thermocycling, resins and methods
Ver menos
Consani, Rafael Leonardo Xediek, 1974-
Orientador
Freitas, Anderson Pinheiro de
Avaliador
Oliveira, Luciana Valadares
Avaliador
Mesquita, Marcelo Ferraz, 1967-
Avaliador
Guiraldo, Ricardo Danil
Avaliador
Influencia da termociclagem, escovação mecanica e desinfecção quimica na dureza Knoop e rugosidade de superficie de resinas acrilicas com diferentes ciclos de polimerização
Andrea Fabiana de Lira
Influencia da termociclagem, escovação mecanica e desinfecção quimica na dureza Knoop e rugosidade de superficie de resinas acrilicas com diferentes ciclos de polimerização
Andrea Fabiana de Lira
Exemplares
Nº de exemplares: 1
Não existem reservas para esta obra