Avaliação da tixoconformabilidade de ligas Al-Xwt%Si-2,5wt%Cu-0,5wt%Mg
Davi Munhoz Benati
DISSERTAÇÃO
Português
T/UNICAMP B431a
[Evaluation of thixoconformability of Al-Xwt%Si-2,5wt%Cu-0,5wt%Mg alloys]
Campinas, SP : [s.n.], 2008.
133p. : il.
Orientador: Eugenio Jose Zoqui
Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecanica
Resumo: Este trabalho teve co:mo objetivo avaliar a tixoconformabilidade de ligas Al-Xwt%Si2,5wt%Cu-0,5wt%Mg, abrangendo desde a obtenção das ligas tixofundidas até sua completa caracterização em termos de macro e microestrutura e comportamento viscoso. Ligas Al-1,Owt%Si-2,5wt%Cu-0,5wt%Mg,...
Ver mais
Resumo: Este trabalho teve co:mo objetivo avaliar a tixoconformabilidade de ligas Al-Xwt%Si2,5wt%Cu-0,5wt%Mg, abrangendo desde a obtenção das ligas tixofundidas até sua completa caracterização em termos de macro e microestrutura e comportamento viscoso. Ligas Al-1,Owt%Si-2,5wt%Cu-0,5wt%Mg, Al-2,Owt%Si-2,5wt%Cu-0,5wt%Mg, Al-4,Owt%Si2,5wt%Cu-0,5wt%Mg e Al-7,Owt%Si-2,5wt%Cu-0,5wt%Mg foram produzidas via ultra-refino de grãos utilizando o refinador Al-5,Owt%Ti-l,Owt%B. Os materiais foram submetidos a tratamentos térmicos de reaquecimento pelos.tempos de Os, 30s, 90s e 21Os, para duas condições de frações sólidas, 45% e 60%. As ligas contendo 1,Owt%Si, 2,Owt%Si e 4,Owt%Si mostraram-se. bastante próximas em termos de viscosidade aparente, no entanto, a liga com 4,Owt%Si apresentou melhor desempenho em termos de globularização, expressa pelo RQI. Já a liga contendo 7,Owt%Si mostrou-se dendrítica para todas as condições estudadas, o que dificulta sua aplicação nos processos de tixoconformação Os tempos de tratamento térmico agem no sentido de promover a globularização das partículas de fase primária, de forma que os melhores resultados de viscosidade foram alcançados para ligas submetidas aos tempos de 21 Os. As frações sólidas de 45% e 60% não apresentaram diferenças significativas em termos de RQI, porém as ligas contendo menor fração sólida apresentaram melhor desempenho em termos de viscosidade aparente, da ordem de 105Pa.s
Ver menos
Abstract: The goal of this work was to evaluate the thixoformability of Al-Xwt%Si-2.5wt%CuO.5wt%Mg alIoys, including the thixocasting of all alloys and their complete characterization in terms of macro and microstructures and rheological behavior. Al-l.0wt%Si-2.5wt%CuO.5wt%Mg,...
Ver mais
Abstract: The goal of this work was to evaluate the thixoformability of Al-Xwt%Si-2.5wt%CuO.5wt%Mg alIoys, including the thixocasting of all alloys and their complete characterization in terms of macro and microstructures and rheological behavior. Al-l.0wt%Si-2.5wt%CuO.5wt%Mg, Al-2.0wt%Si-2.5wt%Cu-0.5wt%Mg, Al-4.0wt%Si-2.5wt%Cu-0.5wt%Mg and Al-7.0wt%Si-2.5wt%Cu-0.5wt%Mg alloys were produced by ultra-refining by addiction of Al5.0wt%Ti-1.0wt%B master alIoy. The materials were submitted to re-heating treatment for Os, 30s, 90s and 2l0s in two conditions, 45% al!d 60% of solid fraction. 1.0wt%Si, 2.0wt%Si and 4.0wt%Si alloys showed very similar results for apparent viscosity, however the 4.0wt%Si alloy showed better performance in terms of globularization, measured by RQI. Thixocast 7.0wt%Si alloy presented dendrictic structures for alI conditions analyzed, making its application too difficult for thixoforming processes. Re-heating treatment times promote the solid phase particles globularization, so that the alloys treated during 210s achieved better results for apparent viscosity. Both 45% and 60% solid fractions did not show significant differences in terms of RQI, but the alloys containing lower solid fraction showed better performance for apparent viscosity, in the order of 105Pa.s
Ver menos
Avaliação da tixoconformabilidade de ligas Al-Xwt%Si-2,5wt%Cu-0,5wt%Mg
Davi Munhoz Benati
Avaliação da tixoconformabilidade de ligas Al-Xwt%Si-2,5wt%Cu-0,5wt%Mg
Davi Munhoz Benati
Exemplares
Nº de exemplares: 2
Não existem reservas para esta obra