Agradecimentos: Financial support from NIH NIDCR (R15-DE023211, U01-DE023756 and K02-DE025280 to CSP) is greatly appreciated. The authors thank FAPESP (Foundation for Research Support of the State of Sao Paulo, Brazil - Grant 16/14217-0) for the financial support for the postdoctoral study provided...

Agradecimentos: Financial support from NIH NIDCR (R15-DE023211, U01-DE023756 and K02-DE025280 to CSP) is greatly appreciated. The authors thank FAPESP (Foundation for Research Support of the State of Sao Paulo, Brazil - Grant 16/14217-0) for the financial support for the postdoctoral study provided to Rafael Leonardo Xediek Consani at Oregon Health & Science University. Special thanks to Dr. Jack F. Ferracane by the relevant assistance. The authors declare no potential conflicts of interest with respect to the material developed in this study

Abstract: Thiourethane (TU) additives and difunctional, polymerizable crosslinking agents have been demonstrated to increase toughness in methacrylate-based materials. The aim of this study was to evaluate the potential reinforcement of acrylic denture bases by combining thiourethane additives and...

Abstract: Thiourethane (TU) additives and difunctional, polymerizable crosslinking agents have been demonstrated to increase toughness in methacrylate-based materials. The aim of this study was to evaluate the potential reinforcement of acrylic denture bases by combining thiourethane additives and 1,6 hexanediol dimethacrylate (HDDMA) as an additional crosslinking agent. One commercial acrylic resin (Nature-Cryl MC; GC America) was tested by adding 0 (control) or 10 wt% TU, each of them combined with 0 (control), 10, 20 and 30 wt% HDDMA, for a total of 8 experimental groups. Materials were processed using microwave energy (500 W for 3 min) using microwave-safe molds and flasks. Flexural strength, modulus and toughness were obtained in 3-point bending (ISO 4049) using bars measuring 2 × 2x25 mm (n = 6). Dynamic mechanical analysis was used to determine glass transition temperature (Tg), breadth of tan delta (as a measure of polymer heterogeneity) and crosslinking density in 1 × 3x15 mm bars (n = 6) tested in tension, using a 3 °C/min heating rate (-30 to 180 °C). Viscosity samples were evaluated in a parallel plate reometer. Data were analyzed by two-way ANOVA and Tukey's test (a = 0.05). Results showed that on the samples not containing TU, HDDMA up to 20 wt% increased the flexural strength and thoughness (and up to 30 wt% HDDMA increased the modulus). The addition of TU did not affect those properties (except for the increase in elastic modulus), but the combination TU + HDDMA led to decreased properties overall. The addition of HDDMA decreased the viscosity for all materials, and the presence of TU did not affect viscosity. The Tg increased linearly with the concentration of HDDMA, except in the groups containing TU – in general, the addition of TU reduced Tg. The crosslinking density increased with the addition of HDDMA for all materials, regardless of the presence of TU. The addition of TU significantly decreased crosslinking density. The breadth of tan delta was not affected by the addition of HDDMA, but significantly increased with the addition of TU. In conclusion, the chain-breaking effect of TU on polymerizing methacrylates was deleterious in the case of methyl methacrylate, since it forms a linear polymer. The addition of HDDMA up to 20 wt% and not combined with TU significantly improved the tested properties

FUNDAÇÃO DE AMPARO À PESQUISA DO ESTADO DE SÃO PAULO - FAPESP

16/14217-0

Fechado