Phase transformation of Nb2O5 during the formation of flame sprayed coatings and its influence on the adhesion strength, abrasive wear and slurry erosive wear
ARTIGO
Inglês
Agradecimentos: Carlos Lima and Hipólito Fals acknowledge the support of São Paulo Research Foundation (FAPESP), Grant #2017/25363-0. Leonardo Fanton also thanks the support of FAPESP, Grant #2017/16715-0. This work was partially supported by the program FAP-UNIMEP, Grant #FAP-119/17. The authors...
Agradecimentos: Carlos Lima and Hipólito Fals acknowledge the support of São Paulo Research Foundation (FAPESP), Grant #2017/25363-0. Leonardo Fanton also thanks the support of FAPESP, Grant #2017/16715-0. This work was partially supported by the program FAP-UNIMEP, Grant #FAP-119/17. The authors also thank Prof. Rubens Caran from UNICAMP, for technical support
The development of research related to the characterization of niobium pentoxide (Nb2O5) has been of great interest in the scientific and commercial community due to promising performances in bio-electrochemical applications, advanced catalysts and corrosive environments. In this work, layers of 250...
The development of research related to the characterization of niobium pentoxide (Nb2O5) has been of great interest in the scientific and commercial community due to promising performances in bio-electrochemical applications, advanced catalysts and corrosive environments. In this work, layers of 250 mu m, 350 mu m and 550 mu m of Nb2O5 were deposited by low-speed flame spray on NiAl-bond coated AISI 1020 steel substrates. The phase transformations of Nb2O5, which occur during the formation of the layers, were studied as a function of deposited thickness and further correlated with adhesion, abrasion and slurry erosion resistance. X-ray diffraction analyzes of the coatings were performed for the study of the phases in the process. Optical Microscopy (OM) and Scanning Electron Microscopy (SEM) with dispersive energy microanalysis (EDS) were used to help microstructural analysis. The adhesive strength of the layers was evaluated by ASTM C633-13 and correlated with abrasion (ASTM G65-16) and slurry erosion wear resistance. From the microscopy analysis, a dense layer was observed with good interconnection at the interface Nb2O5 -NiAl, with presence of pores typical of the thermal spray process. The XRD diffractograms of the niobium oxide coated samples show similar results regardless of the coating thickness (250, 350 and 550 mu m) presenting superior compatibility with the hexagonal Nb2O5 and the monoclinic NbO2.46 (Nb22O54). The significantly higher intensities of the hexagonal Nb2O5 peaks suggest that it is the predominant phase. The thinner coatings, 250 and 350 mu m, had higher adhesive strength, with a mean fracture stress of 16.12 MPa and 15.27 MPa, respectively. Nb2O5 thinner coatings showed also higher abrasive wear resistance when compared to "D2" tool steel and "H13" chrome tool steel. The thicker coatings (550 mu m) had a mean adhesive strength of 13.73 MPa. From the abrasive wear tests, thicker coatings showed a greater volume loss of 41.18 mm(3). The 550 mu m coating presented higher slurry erosion resistance at a 30 degrees particle impact angle, with a lower volume loss (12.93 mm(3))
FUNDAÇÃO DE AMPARO À PESQUISA DO ESTADO DE SÃO PAULO - FAPESP
2017/25363-0; 2017/16715-0
Fechado
Phase transformation of Nb2O5 during the formation of flame sprayed coatings and its influence on the adhesion strength, abrasive wear and slurry erosive wear
Phase transformation of Nb2O5 during the formation of flame sprayed coatings and its influence on the adhesion strength, abrasive wear and slurry erosive wear
Fontes
Wear: an international journal on the science and technology of friction, lubrication and wear Vol. 426-427 (Apr., 2019), p. 277-284 |